You can then activate the hotspot mode by simultaneously pressing the two buttons.ĭelete the connection directly on the VR300 by resetting the WLAN module. If the Wi-Fi light does not flash slowly, it is recommended to perform a WLAN reset. You activate the WLAN module and thus the hotspot mode by simultaneously pressing the Spot and Eco buttons for three seconds. If the module is only grey, it is not switched on. Then, as described above, you must navigate back to the start page using the back button in order to be able to reactivate the WLAN.įor VR300, the Wi-Fi module of your robot must be activated, as you can see from the slow pulsing of the WLAN symbol. If the VR200 was already connected to the WLAN, you first have to press "Remove WLAN" in the "Configure WLAN" section, which will disable the WLAN. After that, use the back arrow to navigate back to the start page of the display. Just follow the instructions in the Kobold robot app.Īctivating the hotspot mode in order to connect to WLANįor VR200, you can access the menu via the "OK" button on the robot, where you navigate to an area where you select "Settings" and then "Configure WLAN" you can put a check on WLAN. The VR Robot network is just the hotspot of the VR300 and does not provide an internet connection, but only serves as the connection point of the robot to the selected WLAN. If you get messages like "NO INTERNET CONNECTION" or "UNSECURED NETWORK", there is no reason to panic. Make sure your router is switched on and that you have disabled the child lock. router may switch off overnight in order to save power or you have set up a child lock topic For additional assistance contact your internet provider.Ħ. If your router does not have such security settings, you can control the sharing of individual devices via your router. Adjust your settings accordingly and run the setup process again. High and medium security settings can cause connectivity issues with our cloud service. Typically, firewalls have a low, medium and high security setting.
If you cannot connect to the server in the last step of the setup process, it may be necessary to make changes to your router's firewall or port settings. You can check the router frequency in the router settings in the web browser. The VR200 only harmonizes with the frequency of 2.4GHz, while the VR300 communicates with 2.4GHz and 5.0GHz. However, you can find your hidden WLAN via the button "Search for other WLANs" if you enter its name correctly.Īlso, your router may have stored an incorrect router frequency in the settings. Your router may hide its network name (SSID). To do this, put all devices that have already been connected to VR Robot once in “flight” mode. Make sure that no other smartphone or tablet connects to the VR Robot during the integration. Therefore, the base station of the VR200 / 300 should be placed as close to the WLAN router as possible. In such cases, the Kobold robot vacuum cleaner cannot build a stable Internet connection. The WLAN signal may be too weak because the robot at the base station is too far away from the router or the WLAN signal is disturbed by reinforced concrete walls or other objects such as metal cabinets or wall-high radiators. The MAC address can be found on the back of your robot. It contains 12 characters in B3 format: 67: JG. When you select a cellular device as your Internet connection, the menu icon changes to indicate your Mac is currently linked to the device ( ).It may be necessary to manually insert the MAC address of your vacuum robot in the router settings in the web browser. When your iOS device is configured properly and is near your Mac, it appears in the Wi-Fi menu as an available connection. Use a cellular device as your Wi-Fi connectionĭepending on your cellular plan, your iPhone or iPad with cellular can share its Internet connection with your Mac.
If you don't know the network password, check with the owner of the Wi-Fi network you're trying to join.
#Wifi cleaner mac app password#
After you select your network, enter the network password when you're prompted. Networks that have a lock icon next to their name require a password. More darkened bars indicate a stronger network connection. The strength of each nearby network is shown next to its name. You can connect to a hidden network by choosing "Join other network" and entering the name of the network you're trying to use. If you don't see your network listed, make sure it's nearby and that others can connect to it.
0 kommentar(er)
